৬৫° টাংস্টেন কার্বাইড রেডিয়াস এন্ড মিলগুলি প্রধানত হার্ডেনড স্টিল, মোল্ড স্টিল, অ্যালয় স্টিল এবং এইচআরসি ৬৫ বা তার নিচে থাকা অন্যান্য উচ্চ-কঠিনতার উপকরণ মেশিনিংয়ের জন্য ব্যবহৃত হয়। এগুলি উচ্চ-গতির রাফিং থেকে ফিনিশিং পর্যন্ত উপযুক্ত এবং মোল্ড ক্যাভিটি, বাঁকা পৃষ্ঠ এবং খাড়া পৃষ্ঠ মেশিনিংয়ের সময় বিশেষভাবে উচ্চ দক্ষতা প্রদান করে।
Typical Machining Cases
মোল্ড ক্যাভিটি মেশিনিং (মাস্টারক্যাম কেস): একটি Φ২৫R৫ ইনডেক্সেবল ইনসার্ট রেডিয়াস এন্ড মিল পিছনের ছাঁচের বিভাজন পৃষ্ঠে বাঁকা রাফিং এবং পকেট রাফিংয়ের জন্য ব্যবহৃত হয়, যেখানে মেশিনিংয়ের মার্জিন ০.৩ মিমি। তারপর একটি Φ১৬R০.৮ রেডিয়াস এন্ড মিল কনট্যুর সেমি-ফিনিশিংয়ের জন্য একটি ধ্রুবক Z-উচ্চতা (০.১৫ মিমি মার্জিন) সহ ব্যবহার করা হয়, তারপরে ০.০ মিমি পর্যন্ত ফিনিশিং করা হয়।
হাউজিং পার্ট মেশিনিং: একটি Φ২৫R৫ রেডিয়াস এন্ড মিল প্রথমে পিছনের ছাঁচের ক্যাভিটি প্ল্যাটফর্মের উপরের বাঁকা পৃষ্ঠের রাফিংয়ের জন্য ব্যবহৃত হয়। তারপর ২ডি কনট্যুর টুলপাথগুলি ফিলের প্রোফাইলের রাফিং এবং ফিনিশিংয়ের জন্য প্রয়োগ করা হয়, ওয়ার্কটেবলের সাথে সংঘর্ষ এড়াতে একটি ০.১ মিমি Z-অক্ষ মার্জিন রেখে।
খাড়া পৃষ্ঠ মেশিনিং: যখন ঢাল ৫ ডিগ্রির বেশি হয়, তখন ফ্ল্যাট এন্ড মিলের পরিবর্তে রেডিয়াস এন্ড মিল বা বল নোজ এন্ড মিল সুপারিশ করা হয়, কারণ টুলের ডগা ক্ষয়প্রবণ এবং মাত্রিক নির্ভুলতার অভাব ঘটায়।
⚙️ Recommended Process Parameters
Roughing Stepover: Set the XY stepover to 55%~85% of the effective cutter diameter
Finishing Stepover: Set the XY stepover to 40%~45% of the effective cutter diameter
Tool Selection: Use radius end mills or high-feed milling cutters for roughing; ball nose end mills for finishing; ball nose end mills, flat end mills or radius end mills for corner cleaning
Radius Matching: Select the R value of the radius end mill according to the Z-direction radius and XY-direction radius of the mold, and take the Z-axis depth of cut, spindle load and chip evacuation capacity into consideration.
⚠️ Notes
The 65° radius end mill is suitable for heat-treated steel below HRC 65. It can be used continuously from roughing to finishing to reduce tool change times.
Radius end mills have cutting edge blind zones. A "top-edge interference" issue may occur in recessed areas, requiring secondary roughing for supplementary machining.
When machining high-hardness materials, tools with TiSiN or AlTiCrN coating are recommended for better heat resistance and anti-adhesion performance.