These HSS Co cobalt twist drill bits cover 0.5 mm to 8 mm with a straight shank and a 135 degree split point, and they are made for the job that most small workshops actually do: drilling steel and stainless steel with a hand electric drill. The 5 percent cobalt HSS holds hardness at HRC 64-66, so the edge survives the heat of a hand drilling pass where a standard HSS bit softens and stops cutting. The split point (four facet) touches the surface at the center, so the bit does not walk on curved pipe, tube or a punched center mark. The black oxide surface reduces friction and holds cutting oil on the flute, which matters most on stainless steel where the material work hardens under a sliding edge.
![]()
Example: D6.0 x 93 - HSS Co 5% - 135 deg split point
| Diameter | Overall Length | Flute Length | Shank Dia. | Point Angle | Material |
|---|---|---|---|---|---|
| 0.5 - 1.0 mm | 24 - 34 mm | 6 - 12 mm | 0.5 - 1.0 mm | 135 deg | HSS Co 5% |
| 1.1 - 2.0 mm | 36 - 49 mm | 12 - 24 mm | 1.1 - 2.0 mm | 135 deg | HSS Co 5% |
| 2.1 - 3.0 mm | 49 - 66 mm | 24 - 33 mm | 2.1 - 3.0 mm | 135 deg | HSS Co 5% |
| 3.1 - 4.0 mm | 66 - 75 mm | 33 - 43 mm | 3.1 - 4.0 mm | 135 deg | HSS Co 5% |
| 4.1 - 6.0 mm | 75 - 93 mm | 43 - 57 mm | 4.1 - 6.0 mm | 135 deg | HSS Co 5% |
| 6.1 - 8.0 mm | 117 - 117 mm | 69 - 75 mm | 6.1 - 8.0 mm | 135 deg | HSS Co 5% |
Bits are packed in tubes of 10 or in indexed sets of 19 / 25 pieces. TiN coating and 1/2 inch reduced shank versions are available.
| Workpiece / Operation | Recommended Series | Selection Reason |
|---|---|---|
| Stainless steel internal thread M1-M12 | HSS Co Spiral Point Tap | 5% cobalt HSS resists work hardening and galling in 304 / 316 |
| Copper, brass and aluminium tapping | HSS Co Spiral Flute Tap | Polished flute lifts chips out of soft material without tearing |
| PCB, FR4 and copper clad micro holes 0.1-5 mm | Carbide PCB Drill Set | Sub-micron grain carbide with 3.175 mm standard shank |
| R angle, internal radius and edge profiling | Carbide Internal R Mill | Ground R profile, 2 flutes, coated for 55 HRC work |
| Roughing FR4 and abrasive laminate | Carbide Corn Cob Mill | Saw tooth edge removes laminate fast with low heat |
| Steel and stainless hand drilling 0.5-8 mm | HSS Co Twist Drill | 135 degree split point, no walking on curved surfaces |
| Chamfer 45 / 60 / 90 / 120 degree and spot drilling | Carbide Chamfer and Spot Drill | One tool spots the hole and breaks the edge |
| Hardened steel trimming up to HRC 65 | Carbide Chamfer Mill 65 HRC | Ultra fine grain substrate with AlTiN coating |
![]()
![]()
![]()
![]()
![]()
Contact Us at Any Time