This 65 degree solid carbide chamfer end mill is made for edge trimming and chamfering on hardened steel up to HRC 65. The substrate is ultra fine grain carbide (0.3 um) with a matched AlTiN coating, a combination that keeps the chamfer edge from chipping when it enters a hardened edge that has already been heat treated. The straight groove flute is the right geometry for chamfering: it produces a straight, uniform chamfer width along the edge and does not pull the cutter into the part. Two flute cutters are used where chip clearance matters and three flute cutters where surface finish and feed rate matter. Tip diameter is ground small so the chamfer starts exactly at the edge without leaving a step.
![]()
![]()
Example: CM65 - D6 x 65 deg x T1.0 - 3F - AlTiN
| Model | Cutting Dia. | Included Angle | Tip Dia. | Shank Dia. | Overall Length | Flutes |
|---|---|---|---|---|---|---|
| CM65-D4-T0.5 | 4.0 mm | 65 deg | 0.5 mm | 4.0 mm | 50 mm | 2 |
| CM65-D6-T1.0 | 6.0 mm | 65 deg | 1.0 mm | 6.0 mm | 50 mm | 2 |
| CM65-D6-T1.0-3F | 6.0 mm | 65 deg | 1.0 mm | 6.0 mm | 60 mm | 3 |
| CM65-D8-T1.5 | 8.0 mm | 65 deg | 1.5 mm | 8.0 mm | 60 mm | 3 |
| CM65-D10-T2.0 | 10.0 mm | 65 deg | 2.0 mm | 10.0 mm | 75 mm | 3 |
| CM65-D12-T4.0 | 12.0 mm | 65 deg | 4.0 mm | 12.0 mm | 100 mm | 3 |
Angles 60 / 90 / 120 degree and tip diameters from 0.2 mm are produced to order. HRC 70 grade available for powder metallurgy steel.
| Workpiece / Operation | Recommended Series | Selection Reason |
|---|---|---|
| Stainless steel internal thread M1-M12 | HSS Co Spiral Point Tap | 5% cobalt HSS resists work hardening and galling in 304 / 316 |
| Copper, brass and aluminium tapping | HSS Co Spiral Flute Tap | Polished flute lifts chips out of soft material without tearing |
| PCB, FR4 and copper clad micro holes 0.1-5 mm | Carbide PCB Drill Set | Sub-micron grain carbide with 3.175 mm standard shank |
| R angle, internal radius and edge profiling | Carbide Internal R Mill | Ground R profile, 2 flutes, coated for 55 HRC work |
| Roughing FR4 and abrasive laminate | Carbide Corn Cob Mill | Saw tooth edge removes laminate fast with low heat |
| Steel and stainless hand drilling 0.5-8 mm | HSS Co Twist Drill | 135 degree split point, no walking on curved surfaces |
| Chamfer 45 / 60 / 90 / 120 degree and spot drilling | Carbide Chamfer and Spot Drill | One tool spots the hole and breaks the edge |
| Hardened steel trimming up to HRC 65 | Carbide Chamfer Mill 65 HRC | Ultra fine grain substrate with AlTiN coating |
Brand: Huaview | MOQ: 5 pieces | Stock delivery: 3-5 working days | OEM/ODM available (laser marking, custom coating, special diameter, length and shank). Send your workpiece material, hole diameter, thread size or profile drawing, and we confirm the correct model within 24 hours.
![]()
![]()
Contact Us at Any Time